HOME | FAQ | HELP | INFO & SHIPPING | POLICY

FREE SHIPPING! ON ORDERS OF $75 OR MORE
CUSTOMER SERVICE: (321) 821-7421

         MY CART

 
 
Home > >LED Lighting - Downlights, Puck Lights, Ribbon Tape Strips, Drivers or Power Supplies, and LED Bulbs > >LED Ribbon Lighting / Indoor & Outdoor Tapes / Various LED Intensity Levels > >Flexible Ribbon Led Strip 2-Lines
(Non-Waterproof) 98W Per Roll
Click to enlarge

Flexible Ribbon Led Strip 2-Lines
(Non-Waterproof) 98W Per Roll



All our Ex-RBL2 ribbons are now ETL approved

  • EX-RBL2 features 2 line high bightness 3528 SMD Led's on a 16mm (5/8") wide PC board.
  • Input 24V DC
  • Dimmable
  • 98 Watts per 5 meter Roll (16.25') - 6 Watt per foot
  • 1200 pcs of SMD 3528 per Roll (5 meter / 16.25')
  • Lumens: Cool White - 8400lm, Warm White - 7200lm, 120 degrees
  • Colors available: Cool White (EX-RBL2-W), Warm White (EX-RBL2-WW), Yellow (EX-RBL2-YL), Green (EX-RBL2-GR), Blue (EX-RBL2-BL), and Red (EX-RBL2-RD)
  • Cuttable: Every 6 Led's (50mm / 1 15/16")
  • Tracks: Compatible with TRACK8 and Up


  • Product Dimensions



    LED drivers for the EX-RBL2-XX:

    Dimmable:
    EX-48W-24V-LED-DIM
    EX-50W-24V-LED-DIM *SMALLEST DIMENSIONS*
    EX-100W-24V-LED-DIM
    EX-300W-24V-LED-DIM
    EXM-150W-24V-LED-DIM
    EXM-200W-24V-LED-DIM
    EXM-300W-24V-LED-DIM



    Non-dimmable:
    LED-10W 24V DC
    LED-25W 24V DC
    LED-60W 24V DC
    LED-100W 24V DC




    Possible applications with EX-RBL2

  • Cove lighting
  • Architectural lights for canopy, corridor, window, archway
  • Backlight or edge lighting for signage
  • DIY lights for home use- Path and contour marking
  • Decorative lights for holiday, event, show, exhibition


  • Assembly Information

  • Solder connection should only be performed on designated solder pads. During soldering, don't exceed the maximum soldering time of 10 seconds and the maximum soldering temperature of 260 Celsius degrees.
  • The smallest unit (50mm - 6 LEDs) can be removed by cutting with scissors between the designated solder pads.
  • The mounting of the strip is facilitated by means of the double-sided adhesive on the back-surface of the strip. Care must be taken to provide a clean and dry mounting surface, free of oils or silicone coatings as well as dirt partide. The mounting substrate must have sufficient structural integrity. Take care to completely remove the adhesive backing. Once the strip is appropriately positioned. Press on the strip with about 20N/cm2 (refer to ap-plication techniques of 3M adhesive transfer tapes).
  • The minimum bending radius is 2 cm. The strip may be bent over a smaller radius of the circuit board contain-ing no electronic components and such bends should be made once and fixed in position to avoid cyclic fatigue.


  • Safety Information

  • The strip itself and all its components may not be mechanically stressed.
  • Assembly must not damage or destroy conducting paths on the circuit board.
  • Installation of LED ribbon (with power supplies) needs to be made with regard to all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations.
  • Correct electrical polarity needs to be observed. Wrong polarity may destroy the strip.
  • Parallel connection is highly recommended as safe electrical operation mode.
  • Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload and damage the strip.
  • Please ensure that the power supply is of adapters power to operate the total load.
  • When mounting on metallic or otherwise conductive surfaces, there needs to be an electrical isolation points between strip and the mounting surface.
  • Pay attention to standard ESD precautions when installing the strip.
  • Damaged by corrosion will not be honored as a materials defect claim. It is the user's responsibility to provide suitable protection against corrosive agents such as moisture and condensation and other harmful elements.


  • EX-RBL2$238.00


    FREE SHIPPING!
    ON ORDERS OF $75 OR MORE
    (UPS Ground Residential)
    $18 MINIMUM ORDER
    EXPRESS LIGHTING CORP
    FLORIDA, USA
    + TEL (321) 821-7421
    © 2000-2023 Express Lighting, All Rights Reserved.